PocketWizard PowerST4 Receiver


ControlTL

PocketWizard’s new firmware platform taps into the full potential of your camera and flash system enabling an entirely new level of remote flash capability through our proven radio communications. ControlTL firmware is configurable and upgradeable for “future-proof” continuous improvement.

Manual Power Control

When the PowerST4 is paired with either the MiniTT1 or FlexTT5 on camera, you can adjust the power settings of your Elinchrom RX lights from the camera’s position either with the Flash Exposure Compensation dial or add the AC3 ZoneController for three zones of power control.

ZoneControl

Use either the AC3 ZoneController or a MultiMAX radio to control up to three zones of light with as many lights in each zone as you want. Use the A-B-C zone switch on the PowerST4 to assign the zone.

PowerTracking

In Auto Mode, change ISO, aperture, or FEC and the lights automatically adjust their compensating power setting with PocketWizard PowerTracking. Set your AC3 ZoneController to manual and PowerTracking is turned off for absolute manual control. PowerTracking can be customized via the PocketWizard Utility.

HyperSync™

HyperSync allows photographers to achieve faster X-sync speeds, all the way up to 1/8000 second*, will full power flash. Now you can cut the ambient light and use wide-open apertures, outdoors in bright sunlight. That extra speed can also freeze action, whether shooting models or athletes in motion. (*camera and flash model dependent).

HyperSync Automation

With ControTL Firmware updates to the MiniTT1 and FlexTT5 for Canon (6.0) and Nikon (3.0) and firmware update 5.1 for the PowerST4, adjusting HyperSync has now been automated. HyperSync can now be adjusted in two seperate places - – on the transmitter and on the receiving ControlTL radio. The transmitting or on-camera MiniTT1 or FlexTT5 automatically adjusts HyperSync to compensate for changes made to shutter speed. Photographers can further refine HyperSync via the PocketWizard Utility. Please visit http://wiki.pocketwizard.com/HyperSync to learn more about configuring HyperSync with a PowerST4.

Programmable and Upgradeable

Use the PocketWizard Utility with the PowerST4’s USB port to program the receiver to any PocketWizard channel and zone. You can also program your initial power settings, modeling light settings and beeper settings using the Utility. The PowerST4 can be easily upgraded whenever updates and feature enhancements are available.

Channels/Learn Mode

The PowerST4 can be programmed as needed with up to 20 ControlTL channels for Manual Power Control, or 32 standard channels for simple triggering. Channels can be configured with the PocketWizard Utility, the Learn function from another PocketWizard radio, or the reset function to configure back to factory settings.

Reverse Compatible

The PowerST4 Receiver operates on the same channels as all other PocketWizard radios and will work with any PocketWizard radio you may already have.

Low-Profile Design

The PowerST4 is tiny and simply plugs into the remote socket on an Elinchrom RX flash. Note: Ranger RX requires EL-19374 EL Skyport Transceiver RX Adapter.

No batteries required

The PowerST4 gets its power from the flash.

Frequency:

FCC/IC model: 340.00 - 354.00 North America
CE model: 433.42 - 434.42 MHz EU/Asia/Other

Channels:

52 Channels over 26 Frequencies - FCC/IC
35 Channels over 5 Frequencies - CE

Antenna:

2.7" (6.9 cm) rubberized

Mounting:

Five-pin remote socket

Zone Select Switch:

A-B-C

Status Indicator:

LED: Green, Amber, Red Status indications

USB:

USB Compliant 2.0, Mini-B Connector, 5VDC regulated, 100mA, Pin 1 Positive, Pin 4 Ground

Operating temperature:

Above -15° C (5° F) and below 50° C (120° F)

Storage
temperature:
(without battery)

Above -30° C (22° F) and below 85° C (185° F)

Construction:

High impact plastic, rubberized antenna

Power:

Receives power from attached flash

Dimensions:

3.6" (9.2cm) long x 2.2" (5.5 cm) wide x 1" (2.5 cm) tall

Weight:

.77 ounces (21.83 grams)

Included in the box:

PowerST4 Receiver, Quick Guide

RoHS Compliant

Requirements:

Must be used in conjunction with a MiniTT1 or FlexTT5 on camera for power control capability. May be paired with any PocketWizard transmitter or transceiver for simple triggering.

PocketWizard

PocketWizard

Whether firing a remote camera, using TTL flash for a wedding or portrait or working in a commercial studio with studio power packs and heads. PocketWizard’s wireless triggering systems make it possible. PocketWizard radio systems enable untethered triggering between all components of a photographic system, no matter how simple or complex the remote triggering needs. With features such as E-TTL II for Canon & CLS / i-TTL for Nikon, PocketWizard have a reliable solution for off-camera TTL flash or remote camera operation allowing triggering up to 500m.