PocketWizard FlexTT5 Transceiver
Manual Power Control
Remotely adjust the manual power settings of your flashes in up to three zones (groups). You can have as many flashes in each group as you want.
Get more light, faster recycling times and more shots per battery with Panasonic’s High Speed Sync (HSS) mode, optimized by PocketWizard’s ControlTL technology. Now you can take advantage of this great feature and shoot wide open in full sun with remote speedlights.
HyperSync allows photographers to achieve faster X-sync speeds with full power flash. Now you can cut the ambient light and use wide-open apertures outdoors in bright sunlight. That extra speed can also freeze action, whether shooting models or athletes in motion.
*Every camera/flash system performance will be different.
Works with all PocketWizard radios on the same frequency including PocketWizard OEM Partner products like Sekonic meters and Profoto, Bowens, Calumet, Dynalite, Lumedyne, Norman and Photogenic flash packs for standard triggering and HyperSync.
Using a standard USB connection and the free PocketWizard Utility, you can easily configure your channel settings, dial in your HyperSync timing, adjust your sleep-mode timers and update your product to the latest firmware whenever updates are available.
Auto-Sensing Transceiver Technology
PocketWizard’s Auto-Sensing Transceiver Technology enables the FlexTT5 Transceiver to switch between transmit mode and receive mode automatically for greater flexibility on the job.
Easily trigger a remote camera in sync with a remote flash with Auto-Relay Mode. Put a camera where you can’t be and use either remote TTL or non-TTL lighting or both at the same time.
Use your Panasonic camera’s flash menus to control the power of up to 3 Groups (zones) of light.
The FlexTT5 Transceiver has two plug-in ports for use with remote cameras and other flash packs. With its Auto-Relay Mode, the FlexTT5 can trigger a remote camera and transmit to a remote flash at the same time.
Panasonic TTL compatible - Visit http://wiki.pocketwizard.com for updated compatibility list
340.00 - 354.00 MHz US FCC / IC
433.42 - 434.42 MHz CE
52 Channels over 26 Frequencies (FCC/IC)
35 Channels over 5 Frequencies (CE)
2.7" (6.9 cm) rubberized with 180 degree swing
Transmit output power:
Less than 0.001 watt (1/1000 of a watt or 1 milliwatt)
Comparable to other PocketWizard radios (Actual range is dependent on multiple factors including equipment, mode, environment, positioning,
orientation and interference)
Hot Shoe, 1/4-20, lanyard, velcro
Maximum Shooting Rate Frames per second (fps)
TTL Mode: within 1 FPS of camera's maximum FPS
* dependent on flash power settings
FPS = Frames Per Second
Power / Channel Switch
OFF - C.2 - C.1
Zone Select Switch
A-B-C (matches Panasonic Groups/Zones)
LED: Green, Amber, Red status indications
Camera / P1 Port
1/8" (3.5 mm) stereo miniphone for 2-stage remote camera triggering. Port Voltage Handling: up to 50 Volts, 100 milliamp continuous
Tip = Trigger
Ring = Pre-Trigger
Sleeve = Ground
Note: for camera triggering only. Do not connect a flash to this port.
Flash / P2 Port
1/8" (3.5 mm) mono miniphone. Port Voltage Handling: up to 200 Volts, 4 amps peak, 250 milliamp continuous, non-polarized
Minimum Receive Contact Time
Camera / P1 Port = 80 milliseconds
Flash / P2 Port = 500 milliseconds
3.3 VDC (all pins) - safe for all cameras
Hot Shoe voltage protection:
Hot Shoe: up to 50 Volts
USB Compliant 2.0, Mini-B Connector, 5VDC regulated, 100mA, Pin 1 Positive, Pin 4 Ground
Above -15° C (5° F) and below 50° C (120° F).
Storage Temperature (without battery)
Above -30 C (-22 F) and below 85 C (185 F)
High impact plastic, captive battery door
Hot Shoe made of glass reinforced resin
Two (2) AA (IEC:LR6) Alkaline recommended, other chemistries (NiMH, NiCAD, Lithium) allowed, USB
30 + Hours
3.6" (9.2 cm) long x 2.9" (7.3 cm) wide x 1.4" (3.6 cm) tall, antenna lowered
5.4 oz (153 grams) 3.8 oz (108 grams) without batteries